+

Multi-channel sequence start/timing adjustable/cycle on/off/control board module/industrial control panel PLC programmable

USD 28.90

Multi-channel sequence start/timing adjustable/cycle on/off/control board module/industrial control panel PLC programmable

Description
Multi-channel sequence start / timing adjustable / cycle on/off / control board module / industrial control panel PLC programmable
 
1: Product model: YYS-2 The product comes with several common functions, which can control the solenoid valve, water pump, motor, lamp belt, etc.
2: Input voltage: DC 5/12/24V optional; default hair 12V
3: Output power: can control DC or AC load within 5A
4: Time range: 0.1 seconds to 999 minutes, adjustable at any time
 
Wiring port description:
1, DC+: input DC power supply positive
2, DC-: input DC power supply negative
3. IN1~IN6: signal input terminal (NPN, negative trigger)
4, NO: Relay normally open interface, the relay is suspended before the suction, after the pull-in and short with COM
5, COM: relay common interface
6. NC: The relay normally closes the interface, and the relay is shorted to COM before the suction is closed.
 
function list:
P-11: Self-locking: give signal 1; relay 1 starts; signal 1 is sent again; relay 1 stops (six paths are independent of each other; can be triggered separately)
P-12: Interlock: Give signal 1; Relay 1 starts, other relays stop; Give signal 2; Relay 2 starts, other relays stop; (six-way interlock; only one relay is working at the same time)
P-13: Jog: Give signal 1, relay 1 starts; signal 1 disappears, relay 1 stops; (six paths are independent of each other; can be triggered separately)
P-14: give signal 1; relay 1 starts; delay turns off; gives signal 2; relay 2 starts; delay opens; (6 different delay times can be set separately, only one relay is working at the same time) P -21: After power-on; relay delay start (6 different delay times can be set separately)
P-22: After power-on; the relay delays outputting a switch signal (10ms) (6 different delay times can be set separately)
P-23: Give signal 1; relay delay start (6 different delay times can be set separately)
P-24: Give signal 1; relay delay output one switch signal (10ms) (6 different delay times can be set separately)
 
 
 
Button setting description: Power-on display ''---'' means to enter standby mode;
Press K1 for the first time (it takes more than 1 second to be effective to prevent false triggering) Display: P -11: K2K3 adjusts the main mode, K4 adjustment function
Press the second K1, the screen displays: 1 001: K2 and K3 adjust the first time, K4 adjusts the decimal point (time unit)
Press the third K1, the screen displays: 2 001: K2 and K3 adjust the second time,
Pressing the fourth K1, the screen displays: 3 001: K2 and K3 adjust the first time,
Press the fifth K1, the screen displays: 4 001: K2 and K3 adjust the second time,
Press the sixth K1, the screen displays: 5 001: K2 and K3 adjust the first time,
Press the seventh K1, the screen displays: 6 001: K2 and K3 adjust the second time,
Pressing the eighth K1, ''---'' is displayed to enter standby mode.
 
Decimal time unit description:
XX.X decimal point in ten, timing range: 0.1 seconds to 99.9 seconds
XXX has no decimal point, timing range: 1 second ~ 999 seconds
XXX. The decimal point is in one place, the time range is from 1 minute to 999 minutes.
 
Specification

Theory : Time Relay

Model Number : YYS-2

+